Adrian-VTA
Global Moderator
Adelaide, South Australia
Posts: 5,327
|
Post by Adrian-VTA on Mar 16, 2016 17:02:43 GMT -8
Hi Guys, I've had a bunch of crystals come through from a new supplier and I think there might be some that work with this case. It needs a really steep bevel to deal with the bezel. Anyone with this case want to try one?
|
|
cobrajet25
Needs a Life!
"Underweared curmudgeon!"
Posts: 3,357
|
Post by cobrajet25 on Mar 16, 2016 17:28:35 GMT -8
Sure! I'll give it a go for you.
|
|
|
Post by Groundhog66 on Mar 16, 2016 17:44:57 GMT -8
Wish I had a 7006-8030 to try it in.
|
|
HiBeat
Global Moderator
SEIKO Iko Iko GDTRWS
Posts: 8,667
|
Post by HiBeat on Mar 16, 2016 18:46:11 GMT -8
Hey Adrian, I have two acryllic aftermarket crystals designed to be replacements for 310T19AN
GS version PA467-12 SternKreuz XAC 310.583 = 310T19ANS with silver tension ring.
Now I realize you are going mineral replacement, but they might give you an idea of what GS and SK thought the outer profile/inner profile/diameters should have been.
If you want I can toss them into the box with my Pogue for rebuild.
|
|
tritto
WS Benefactor
Posts: 5,873
|
Post by tritto on Mar 16, 2016 18:50:10 GMT -8
Well I have a couple of 7006 8030s that I could try it in. One has the GS above which is a perfect repro. The other has a polished original 310T19AN. The SK referred to above doesn't fit as the bevel edge is too steep and interferes with the bezel. It's also flat topped rather than domed. Happy to switch your repro into one if you need more testers. I could potentially test it in a 7005 8050, which also uses the 310T... Does yours have a slight dome Adrian? Edit: I didn't read the 1 tester needed. Sorry cobrajet25, I didn't mean to try to jump over you.
|
|
cobrajet25
Needs a Life!
"Underweared curmudgeon!"
Posts: 3,357
|
Post by cobrajet25 on Mar 16, 2016 23:55:59 GMT -8
Well I have a couple of 7006 8030s that I could try it in. One has the GS above which is a perfect repro. The other has a polished original 310T19AN. The SK referred to above doesn't fit as the bevel edge is too steep and interferes with the bezel. It's also flat topped rather than domed. Happy to switch your repro into one if you need more testers. I could potentially test it in a 7005 8050, which also uses the 310T... Does yours have a slight dome Adrian? Edit: I didn't read the 1 tester needed. Sorry cobrajet25 , I didn't mean to try to jump over you. No worries. If you are closer, then Adrian can certainly send it to you.
|
|
tritto
WS Benefactor
Posts: 5,873
|
Post by tritto on Mar 18, 2016 18:10:58 GMT -8
Actually, west.au (Steve) is looking for a 310T19AN or a suitable substitute. Perhaps he could give it a try?
|
|
Adrian-VTA
Global Moderator
Adelaide, South Australia
Posts: 5,327
|
Post by Adrian-VTA on Mar 18, 2016 18:15:35 GMT -8
Geday,
Took a day off (mostly) yesterday.
I'll get a few as these are pretty low cost and the quality is very high and send them out to you guys.
Worst case scenario you can use them on other projects (the 31mm crystals are for the most part interchangeable)
|
|